塑钢线在包装时怎么打包？ How to pack plastic steel wire when packing?

塑钢线打包的步骤： 

1.缠绕塑钢带用缠绕铝卷一周后，将塑钢带叠加对齐，塑钢带头在下。

2.装塑钢带握紧打包机手柄，将塑钢带放入打包机，并分离开一定距离。

3.装塑钢带（将塑钢带完全穿进打包机，使塑钢带上、下部分处在裁的上下位置，调整塑钢带对齐并完全放进打包机。

4.束紧  按住张紧开关柄，一次性完成束紧，严禁点动。

5.热合  按住热合开关柄（振动开关柄）3~5秒钟。

6.泄压 热合后等待约3秒钟，点一下手柄下方的泄压开关。 

7.完成打包握紧手柄将打包机从侧边抽出。

塑钢线在打包时的注意事项：

 1、打包机应轻拿轻放，不使用时应放 置平稳处，避免摔、砸等损坏。 

 2、确保空压机压力达到正常使用值，气线密封良好，无漏气、打折等情况。

 3、清理张紧轮粘附的碎屑时，应按压手柄将张紧轮和底模分离，防止无带摩擦损坏。 

 4、严禁在无打包带情况下操作设备，打带过程中严禁点动张紧及热合开关，应按住不动，一次性完成张紧、热合过程。 

 5、打包机每周一次从气接入口处用化油清洗剂对气道进行清洗。 

 6、当班作业前给打包机加少量变压器油。

Steps of plastic steel wire packaging:

1. After winding the plastic steel belt with aluminum coil for one week, stack and align the plastic steel belt with the plastic steel head under it.

2. Install the plastic steel belt, hold the handle of the packer tightly, put the plastic steel belt into the packer and separate it at a certain distance.

3. Load plastic steel belt (fully thread the plastic steel belt into the baling machine, make the upper and lower parts of the plastic steel belt in the upper and lower positions of the cutter, adjust the alignment of the plastic steel belt and completely put it into the baling machine.

4. Tighten. Press and hold the tension switch handle to complete the tightening at one time. Inching is strictly prohibited.

5. Press and hold the heat switch handle (vibration switch handle) for 3-5 seconds.

6. Wait for about 3 seconds after pressure relief and hot sealing, and click the pressure relief switch under the handle.

7. Finish packing, hold the handle and pull out the packer from the side.

Precautions for plastic steel wire packaging:

1. The packer should be handled with care. When not in use, it should be placed in a stable place to avoid falling, smashing and other damage.

2. Ensure that the pressure of the air compressor reaches the normal use value, and the air line is well sealed without air leakage, discount, etc.

3. When cleaning the debris adhered to the tensioning wheel, press the handle to separate the tensioning wheel from the bottom mold to prevent damage without belt friction.

4. It is strictly forbidden to operate the equipment without packing belt. It is strictly forbidden to jog the tension and heat sealing switch during the process of playing belt. It should be pressed and held still to complete the tension and heat sealing process at one time.

5. Once a week, the baling machine uses chemical oil cleaning agent to clean the airway from the air connection inlet.

6. Add a small amount of transformer oil to the packer before the operation on duty.